rev. 7.10.09_81 hps3000 series 1 of 7 embedded power for business-critical continuity hps3000 series 3000 watts special features ? 3000 w output power ? 40 w/cu-in ? optional customer provided air ? 1u x 3u form factor ? n+1 redundant ? hot-swap ? internal or-ing ? 5 v housekeeping ? high effciency 89% @ 200 vac, 100% load ? variable speed smart fans ? one year warranty distributed power bulk front-end single output electrical specifcations safety input input range (operating): 180 - 264 vac 90 - 140 vac input range (nominal): 200 vac 110 vac input through card edge connection on same end as dc output frequency: 43 to 63 hz input fusing: internal 25 a fuses both lines fused inrush current: 40 a peak either hot or cold start power factor: 0.97 typical meets en61000-3-2 harmonics: meets iec 1000-3-2 requirements @ 50% load input current: 19 a max input current holdup time: 10 ms minimum at full rated load leakage current: 1.4 ma at 240 vac power line transient: mov directly after the fuse ul/cul 60950 csa 60950 china ccc nemko tuv cb report csa 22.2 60950 ? ? ? ? ? ? compliance poe isolation emi class b - en55022, level a en61000 immunity ? ? ?
rev. 7.10.09_81 hps3000 series of 7 embedded power for business-critical continuity output output rating 48 v @ 62.0 a 5 vsb @ 3.0 a 180 - 264 vac 48 v @ 29.4 a 5v @ 3 a 90 - 140 vac set point 48 v programmable 10% through i 2 c serial bus total regulation range 48 v 10% 5 vsb 4% line/load/transient when measured at output connection rated load 3000 w maximum @ 200 vac input 1500 w maximum @ 110 vac input no derating over operating temp range minimum load 48 v @ 0.0 a 5 vsb @ 0.0 a no loss of regulation output noise 480 mv max p-p 100 mv max p-p 48 v output 5 vsb output measured with a 0.1f ceramic and 10 f tantalum capacitor on any input output voltage overshoot 5% maximum nominal voltage setting transient response 5% maximum deviation 50% load step @ 1 a/us step load valid between 10% to 100% of output rating. max units in parallel up to 4 total power in 1u 19 rack is 12 kw short circuit protection 120% - 130% of rated output output to return output isolation per poe specs >2000 vac forced load sharing within 10% of all shared outputs digital sharing control over current protection (ocp) 120% to 130% 100% to 125% 48 v output 5 vsb output over voltage protection (ovp) 110% to 120% 110% to 125% 48 v output 5 vsb output over temperature protection 10 - 15 deg c above safe operating area both pfc and output converter monitored 5 vsb will operate under overtemperature condition. built in hysteresis 230 vac effciency environmental specifcations vibration/shock: non-operational 5g sine sweep from 5 hz to 500 hz, dwelling at resonant frequencies for 1 hour each operating temperature: -10 to +40 c storage temperature: -40 to +85 c cooling external fans with fan fail and fan speed control operating relative humidity: 5% to 95% non-condensing storage relative humidity: 5% to 95% non-condensing operating altitude up to 10,000 feet above sea level storage altitude: up to 30,000 feet above sea level rohs compliant: yes 2 30v ac e ffi c i en c y 10.0 0 20.0 0 30.0 0 40.0 0 50.0 0 60.0 0 70.0 0 80.0 0 90.0 0 100.00 10 20 30 40 50 60 70 80 90 10 0 % o f t o t al ou t p u t po w e r
embedded power for business-critical continuity embedded power for business-critical continuity 327.6 1. 2 321.4 1. 2 11.9 1 106.7 0. 8 19 11.6 0.5 40 0.8 8 0.5 tyco connector pn: 2007209 or fci 10053363-400lf airflow direction pin assignments bottom top rev. 7.10.09_81 hps3000 series 3 of 7 (all units in mm) pin 64 ac line 63 ac line 62 n.c. 61 ac neutral 60 ac neutral 59 n.c. 58 n.c. 57 n.c. 56 +48 vdc out 55 +48 vdc out 54 +48 vdc out 53 +48 vdc out 52 +48 vdc out 51 +48 vdc out 50 +48 vdc out 49 +48 vdc rtn 48 +48 vdc rtn 47 +48 vdc rtn 46 +48 vdc rtn 45 +48 vdc rtn 44 +48 vdc rtn 43 +48 vdc rtn 42 n.c. 41 sys_gnd 40 stby_sense 39 acok# 38 smbus_alert_out 37 scl 36 a2 35 pskill 34 a1 33 a0 module information pin 1 ac line 2 ac line 3 n.c. 4 ac neutral 5 ac neutral 6 n.c. 7 n.c. 8 n.c. 9 +48 vdc out 10 +48 vdc out 11 +48 vdc out 12 +48 vdc out 13 +48 vdc out 14 +48 vdc out 15 +48 vdc out 16 +48 vdc rtn 17 +48 vdc rtn 18 +48 vdc rtn 19 +48 vdc rtn 20 +48 vdc rtn 21 +48 vdc rtn 22 +48 vdc rtn 23 n.c. 24 v_stby 25 stby_rtn_sense 26 present# 27 dcok/pwok# 28 sda 29 hvcc 30 pson# 31 #alert 32 ishare
embedded power for business-critical continuity rev. 7.10.09_81 hps3000 series 4 of 7 t pw ok _o ff _ ac input main vo ut ti mi ng diagra m t ac_o n_de la y t vout_hol du p t pw ok _o n ac input on / off cy cl e ac_ ok ps_o n 5 vsb vout pw ok ps on on / of f cycl e t sb _o n t sb_vou t t pw ok _del ay t pw ok _o ff _ t pw ok _o ff _ t pw ok _o n t pw ok _o ff _ t pw ok _o n t aco k_ de la y t ps on_on_de la y t ps on_p wo k t pw ok _o ff ac on ac on
rev. 7.10.09_81 hps3000 series 5 of 7 embedded power for business-critical continuity timing signal defnitions turn on/off timing item description min max units tvout_rise 48 v output rise time 5 300 msec tsb_on_delay delay from ac being applied to 5 vsb being within regulation. 1500 msec tac_on_delay delay from ac being applied to all output voltages being within regulation. 2000 msec tvout_holdup time all output voltages, including 5 vsb, stay within regulation after loss of ac. 10 msec tpwok_holdup delay from loss of ac to de-assertion of pwok 5 msec tpson_on_delay delay from pson# active to output voltages within regulation limits. 5 400 msec tpson_pwok delay from pson# de-active to pwok being de-asserted. 50 msec tacok_delay delay from loss of ac input to de-assertion of acok#. 10 msec tpwok_on delay from output voltages within regulation limits to pwok asserted at turn on. 100 1000 msec tpwok_off delay from pwok de-asserted to 48 v dropping out of regulation limits. 1 1000 msec tpwok_low duration of pwok being in the de-asserted state during an off/on cycle using ac or the pson# signal. 100 msec tsb_vout delay from 5 vsb being in regulation to 48 v being in regulation at ac turn on. 50 2000 msec pson # the pson# signal is required to remotely turn on/off the power supply. pson# is an active low signal that turns on the 48 v power rail. when this signal is not pulled low by the system, or left open, the 48 v output turns off. the 5 vsb output remains on. this signal is pulled to a standby voltage by a pull-up resistor internal to the power supply. the power supply fan(s) shall operate at the lowest speed. pson# signal characteristic signal type accepts an open collector/drain input from the system. pulled-up to the 5 vsb located in power supply. pson# = low on pson# = open off min max logic level low (power supply on) 0 v 0.8 v logic level high (power supply off) 2.0 v 4.80 v source current, vpson = low -- 4 ma power up delay: tpson_on_delay 5 msec 400 msec signals and controls - all models
rev. 7.10.09_81 hps3000 series 6 of 7 embedded power for business-critical continuity pwok# (power good) pwok# is a power good signal and will be pulled low by the power supply to indicate that both the outputs are above the regulation limits of the power supply. when any output voltage falls below regulation limits or when ac power has been removed for a time suffciently long so that power supply operation is no longer guaranteed, pwok will be de-asserted to a high state. the start of the pwok# delay time shall be inhibited as long as the 48 v output is in current limit or the 5 vsb output is below the regulation limit. power supply present indicator (present#) the present# signal is primarily used to provide a mechanism by which the host system can sense the number of power supplies physically present (operational or not). this pin is connected to ground in the power supply. ac input present indicator (acok#) the ac ok# signal is used to indicate presence of ac input to the power supply. this signal shall be connected to 5 vsb through a resistor on the host system side. a logic low level on this signal shall indicate ac input to the power supply is present. a logic high on this signal shall indicate a loss of ac input to the power supply. table 12 acok# signal characteristics signal type pull-up to 5 vsb through a resistor in the host system. present# = low present present# = high not present min max logic level low voltage, ising=4ma 0 v 0.8 v logic level high voltage, isink=50a 2.0 v 4.80 v sink current, present# = low 4 ma source current, present# = high 50 a pson# signal characteristic signal type open collector/drain output from power supply. pullup to 5 vsb external to the power supply. pwok = high on pwok = low off min max logic level low voltage, isink=4ma 0 v 0.8 v logic level high voltage, isource=200a 2.0 v 4.80 v sink current, pwok = low 4 ma source current, pwok = high 2 ma pwok delay: t pwok on 100 msec 1000 msec pwok rise and fall time 100 sec power down delay: t pwok off 1 msec 1000 msec
rev. 7.10.09_81 hps3000 series 7 of 7 embedded power for business-critical continuity led indicators there will be a green power led (pwr) to indicate that ac is applied to the psu and standby voltage is available when blinking. this same led should go solid when the 48 v output is enabled and operational. there will be an amber power supply fail led (fail) to indicate that the power supply has failed and a replacement of the unit is necessary. faults including uvp, ovp, otp, or fan fail when pson# is asserted logic low shall cause the amber led to turn on. the led can be turned off by recycling pson# signal or by an ac power interruption more than 1 second. the led shall be off when pson# is not asserted logic low. refer to table 13 for conditions of the leds: mtbf the power supply has a minimum mtbf of 300k hours using the bell core 332, issue 6 specifcation @ 25 c and 40 c , ambient, at full load. with the power supply installed in a system in a 25 c ambient environment and operating at full load, capacitor life shall be 10 years, minimum for all electrolytic capacitors contained within this power supply. the power supply shall demonstrate a mtbf level of > 500,000 hours. quality assurance full qav testing shall be conducted in accordance with emerson network power standards with reports available upon request. warranty emerson network power shall warrant the power supply to be free of defects in materials and workmanship for a minimum period of one year from the date of shipment, when operated within specifcations. the warranty shall be fully transferable to the end owner of the equipment powered by the supply. table 13 led indicators power supply condition power led (green) fail led (amber) no ac power to psu off off ac present / standby output on blinking off power supply 48 v output on and ok on off power supply failure (includes overvoltage, overtemperature) off on current limit on blinking model number main output main output current standby output standby current HPS3000-9 48 vdc 62.0 a 5.0 v 3.0 a ordering information americas 5810 van allen way carlsbad, ca 92008 usa telephone: +1 760 930 4600 facsimile: +1 760 930 0698 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom telephone: +44 (0) 1384 842 211 facsimile: +44 (0) 1384 843 355 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong telephone: +852 2176 3333 facsimile: +852 2176 3888 for global contact, visit: www.powerconversion.com techsupport.embeddedpower@ emerson.com while every precaution has been taken to ensure accuracy and completeness in this literature, emerson network power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. emerson network power and the emerson network power logo are trademarks and ser - vice marks of emerson electric co. ?2009 emerson electric co. emersonnetworkpower.com embedded computing embedded power monitoring outside plant power switching & controls precision cooling racks & integrated cabinets services surge protection emerson network power. the global leader in enabling business-critical continuity. ac power connectivity dc power
|
